H2O miniBOSS Oily Water Separator
BOSS Separators
Separator Spares & Equipment, LLC is an Authorized Service Center and Distributor for H2O BOSS Oily Water Separators. In 2021, H2O, LLC acquired the assests of BOSS Separators, oily water separators designed for the maritime industry.
Separator Design
The miniBOSS oily water separator is a USCG 107(49) certified alternative to a full-blown oily water separator. This unit does not attempt to separate the oil but adsorb it in a series of filters. The key is in the filters. The first filter is a 2.5” x 20” sediment filter. These are inexpensive and available everywhere. In reality, this sediment filter and the solids remove a lot of oil. This sediment filter is followed by two (2) BOSS Extreme filter cartridges. These are 4” x 20” (big blue sized) cartridges that have been tested and proven for years.
These cartridges are the key to the performance of the miniBOSS and are the only approved cartridges that satisfy the 107(49) regulations. The BOSS Extreme filter cartridges do a great job of removing all of the oil right up until they reach their capacity.
The miniBOSS oily water separator is designed for low volume (2.2 GPM (0.45 m3/hr)) applications as an affordable solution to the bilge water disposal problem. The miniBOSS has an IMO MEPC 107(49) certified oil content monitor. This is the same monitor that other oil water separators use and has all of the features, including tracking 18 months’ worth of data. Also included are a process pump and a 3-way diversion valve, just like a full-blown separator.
MiniBOSS oily water separator is mounted on a wall and takes up very little space. It is perfect for a smaller vessel that needs certification but has a low volume.
Features & Advantages:
- Low Capital Cost
- Simple to Install and Operate
- Low Maintenance
- Small Footprint (Wall Mounted)
- IMO Certified Oil Content Monitor
- Flow Rate: 0.45 m3/hr (2.2 GPM)
- Electric Diaphragm Displacement Process Pump
- Fine Solids and Oil removed by Simple Filtration
- Dimensions: 34″ W x 40″ H x 10″ D
How does the miniBOSS oily water separator work?
The miniBOSS oily water separator draws in bilge water using the diaphragm pump (#1) through the system inlet (#11). The pump is fitted with a #20 mesh screen to help prevent damage to the pump. The pump then pushes the bilge water to the first of three cartridges.
The first cartridge (#9) is a 5-micron sediment cartridge, the second (#8) and third (#7) are oil removal cartridges. The pre-sediment pressure gauge (#10) and the post-polisher pressure gauge (#6) will aid you in determining when it is time to change the sediment (#9) cartridge.
Once the bilge water has passed through the polishing cartridges, the Oil Content Monitor (#3) takes a continuous sample and will determine if the oil content is above or below the 15 PPM limit. If it is greater than 15 PPM, the Recycle valve (#4) will open and return the rejected water to the bilge. If the sample is less than 15 PPM, the discharge valve (#5) will open and discharge it overboard.
The polishing cartridges will hold about 10oz of oil each. The sediment cartridge will also aid in the removal of oil droplets that are greater than 5 microns in size. The amount of oil in your bilge will ultimately determine how long each cartridge will last. You will most likely change out the sediment cartridge more frequently than the polishing cartridges. The polishing cartridges are both replaced at the same time when the Oil Content monitor will no longer reach less than 15 PPM.
Need miniBOSS oily water separator parts?
Separator Spares & Equipment, LLC specializes in spare parts, consumables, equipment, and services for BOSS oil water separators and oil content monitors.
BOSS oily water separators are designed to separate oil and water mixtures (bilge water) into separate components before discharging from the vessel. We are committed to keeping your current oil-water separator environmentally compliant with USCG and IMO requirements. We are your link to IMO MEPC 107(49) compliance.
To learn more about oil water separator spare parts, visit our Oily Water Separator Spare Parts webpage.
Need your miniBOSS oily water separator serviced?
Separator Spares & Equipment, LLC offers a full range of services for BOSS oily water separators and oil content monitors. We are committed to keeping your current miniBOSS oily water separator environmentally compliant with US Coast Guard and IMO MEPC 107(49) requirements. We can provide scheduled maintenance services to assist the operator in essential maintenance functions.
With our experience in oily water separators, Separator Spares & Equipment can provide the following services:
– Recovered Energy factory-trained service technicians
– Repair and service your BOSS separators
– Recalibrate and service your oil content monitors
– Train personnel in your particular oily bilge water separator
– Genuine Recovered Energy spare parts
– Replacement oil content monitors
– New IMO MEPC 107(49) certified oily water separators
To learn more, visit our Oil Water Separator Service and Solutions webpage.
Downloads
Similar Products
